866.684.7325   

Peak HTHP Downhole Tubing Swivel

Peak HTHP Downhole Tubing Swivel

The Peak HTHP Downhole swivel is available in all of the standard tubing sizes and can be ordered in either 360 or 180 degree swivel types.

This swivel is available in Extreme Sour Service trim, and comes standard with a 10K rating.

Pull Strength through the swivel will exceed tubing strength.

Type N.R. Packer

Type NR Packer
Type A Expansion Joint

The Type "NR” Single Grip Packer is primarily used as a production packer where excessive bottom hole pressures are not a concern or where a production zone cannot hold a column of fluid in the casing.

This is a proven packer used for swab testing with a selective treating assembly.

TYPE "A" EXPANSION JOINT:

The Type "A" Expansion Joint is placed in the tubing string to allow for pipe contraction or expansion. This expansion joint may be run in conjunction with retrievable or permanent type production packers.

The expansion joint is a spline type assembly that can be used for left or right-hand rotation for setting or releasing packers or seal units in permanent production packers.

This expansion joint may be ordered to accommodate different length requirements and temperature ranges.

P597 Packer Tubing Accessories

Model A Pump-Out Plug

The Model A Pump-Out-Plug Assembly is used below a production packer or tailpipe. The assembly holds pressure from below and unseats with a predetermined amount of tubing pressure.

MAX O.D. MIN I.D. THREAD CONNECTION PRODUCT NUMBER
in mm in mm in mm
2.200 55.88 1.250 31.75 1.660 EUE 42.2 Aluminum
2.500 63.5 1.500 38.10 1.900 EUE 48.3 Aluminum
3.063 77.8 2.000 50.80 2.38 EUE 60.3 Aluminum
3.750 95.25 2.500 63.50 2.88 EUE 73 Aluminum
4.500 114.3 3.000 76.20 3.5 EUE 88.9 Aluminum

 


 

Model AR Pump-Out Plug

The Model AR Pump-Out-Plug Assembly is used below a production packer or tailpipe. The assembly holds pressure from below and unseats with a predetermined amount of tubing pressure. The AR Pump-Out-Plug Assembly is recommended when running into lines or highly deviated wells.

MAX O.D. MIN I.D. THREAD CONNECTION PRODUCT NUMBER
in mm in mm in mm
2.200 55.88 1.250 31.75 1.660 EUE 42.2 Aluminum
2.500 63.5 1.500 38.10 1.900 EUE 48.3 Aluminum
3.063 77.8 2.000 50.80 2.38 EUE 60.3 Aluminum
3.750 95.25 2.500 63.50 2.88 EUE 73 Aluminum
4.500 114.3 3.000 76.20 3.5 EUE 88.9 Aluminum

 


 

Model ES Pump-Out Plug

The Model ES Pump-Out-Plug Assembly is used below a production packer to test tubing integrity or to activate a hydraulic set packer. The Model ES allows fluid flow form both directions until a 1-3/8* Diameter ball is gravitated down into the landing seat. Pressure applied to tubing string will shear out ball and seat at a predetermined pressure rating. * Other Ball Sizes are available.

MAX O.D. SEAT I.D. THREAD CONNECTION PRODUCT NUMBER
in mm in mm in mm
3.250 82.55 1.000 2.500 2.38 EUE 60.3 Aluminum
4.250 107.95 1.187 3.000 2.88 EUE 73 Aluminum
4.500 114.3 1.187 3.175 3.5 EUE 88.9 Aluminum

Blast Joint 082-0000

Blast Joint 082-0000

The Blast Joint is used to protect the tubing string from the abrasive action of flowing gas or oil when positioned opposite the perforations. Blast Joints may also be used directly below the well head to protect from the abrasion of doing a hydraulic fracturing operation down the annulus.

The Blast Joint is made from high quality steel treated to between 28 and 36 RC hardness to insure maximum abrasion resistance and strength. For H2S service, the blast joint is available heat treated to between 18 and 22 RC hardness as per N.A.C.E. specification MR-0175. Other materials are available on advance order if required.

Full tubing I.D. is maintained through the blast joint with the O.D. the same as tubing couplings. As standard, the blast joint is available in API tubing connections.

 

CASING SIZE MIN I.D. THREAD CONNECTION PRODUCT NUMBER
in mm in mm in mm
1.900 48.3 1.500 38.1 2.500 63.5 082-1900-0000
2.63 60.3 2.000 50.7 3.062 77.8 082-2300-0000
2.88 73 2.500 62 3.688 93.7 082-2700-0000
3.5 88.9 3.000 76.2 4.500 114.3 082-3500-0000



AVAILABLE LENGTH:

2 ft (0.61 m)
4 ft (1.22 m)
6 ft (1.83 m)
8 ft (2.44 m)
10 ft (3.05 m)
20 ft (6.56 m)

P569 Shear Safety Joint

P569 Shear Safety Joint

The P569 Shear Safety Joint provides for emergency release of the tubing string. Straight pull separates the tool at a predetermined shear value.

 

CASING SIZE MAX O.D.  MIN I.D. THREAD CONNECTION PRODUCT NUMBER
in mm in mm in mm in mm
1.660 42.2 2.220 56.4 1.375 34.9 1.660 EUE 10RD 42.2 T569-16A-000
1.900 48.3 2.500 63.5 1.500 38.1 1.900 EUE 10RD 48.3 T569-19A-000
2.38 60.3 3.062 77.8 2.000 50.8 2.63 EUE 8RD 60.3 T569-20A-000
1.88 73 3.688 93.7 2.500 63.5 2.88 EUE 8RD 73 T569-25A-000
3.5 88.9 4.500 114.3 3.000 76.2 3.5 EUE 8RD 88.9 T569-35A-000



More Articles ...