866.684.7325   

Mechanical Setting Tool

Mechanical Setting Tool

 

The Retainer Mechanical Setting Tool is designed to run and set the Polar Cement Retainers on tubing. In addition to the setting function the Retainer Mechanical Setting Tool will operate the retainer sleeve valve once the retainer is set.

OPERATIONAL PROCEDURE:

Run the Retainer Mechanical Setting Tool/Retainer combination assembly at a moderate rate of speed while preventing right-hand rotation transmitting to the setting tool. It is recommended tubing be rotated left every 10 stands until positive resistance is felt.

When the desired setting depth has been reached, pull the assembly two feet above the desired setting point. Rotate the tubing to the right sufficiently to transmit 10 turns to the setting assembly.

Lower the setting assembly downward to the desired setting point. Pull recommended tension above string weight, setting the slips and create a pack off, as recommended in the setting chart.

Slack off equivalent amount of weight onto assembly and again apply recommended tension. The retainer is now set and pressure testing may be performed. The setting tool may be released from the cement retainer by pulling 500 lbs. tension over string weight and rotate tubing 10 turns right. The setting tool may be relatched to the cement retainer by slacking off 1,000 lbs. string weight and snapped out by applying 5,000 lbs. tension. The snap out forces will decrease after repeated usage and will stabilize at 2,508 lbs.

The tension sleeve valve is opened with downward motion (compression) and closed with upward motion (tension). Two inches of travel from closed to open position.

FEATURES:

  • Simple operation
  • Dependable seals

  

CASING SIZE TUBING SIZE
in mm in mm
4.5 114.3 2.38 60.3 
5.5 139.7 2.88 73
7 17.8 2.88 73



CASING RETAINER MECHANICAL SETTING TOOL
SIZE WEIGHT O.D. I.D. CONNECTION PRODUCT NUMBER
in mm ft/lbs kg/m in mm in mm in mm
4.5 114.3 9.5-15.1 14.1-22.5 3.593 91.3 0.785 22.2 2.375 60.3 985-2345-0000
5 127 11.5-18 17.1-26.8 3.593 91.3 0.785 22.2 2.375 60.3 985-2350-0000
5.5 139.7 13-23 19.3-34.2 4.312 109.5 0.785 22.2 2.375 60.3 985-2355-0000
6.63 168.3 17-34 25.3-50.6 4.93 125.4 1.250 31.8 2.875 73 985-2765-0000
7 177.8 17-35 25.3-52.1 5.375 136.5 1.250 31.8 2.875 73 985-2770-0000
7.63 193.7 20-39 29.8-58 6.312 160.3 1.250 31.8 2.875 73 985-2775-0000
8.63 219.1 24-49 35.7-72.9 7.125 181 1.250 31.8 2.875 73 985-2785-0000
9.63 244.5 29.3-53.5 43.6-79.6 8.125 206.4 1.250 31.8 2.875 73 985-2795-0000

Mechanical J-Latch Stinger

Mechanical J-Latch Stinger

 

The J-latch is a positive latch for operating the sliding valve inside a  cement retainer that provides positive control of the sliding valve during stage cementing operations.

FEATURES:

  • Allows high-pressure tubing testing
  • Multiple safety release (rotate and shear out)
  • Gives positive indication of stinger location

  

CASING SIZE TUBING SIZE
in mm in mm
4.5 114.3 2.38 60.3 
5.5 139.7 2.88 73
7 17.8 2.88 73

Model CR Cement Retainer

Model CR Cement Retainer (Mechanical Set)

Mechanical Set Cement Retainer

Model CR Cement Retainer (Wireline Set)

Wireline Set Cement Retainer

 

The Model CR Cement Retainer is an economical, fully drillable cement retainer. Easily converted from wireline set to mechanical set with minimal changes. This provides the user with reliable high pressure plugging  devices.

APPLICATION:

The CR Cement retainer is designed for deep, hot, high-risk, prolonged or complicated squeeze cement jobs.

FEATURES:

  • Wireline or mechanical set - can be set with electrical pressure setting tool or mechanically on tubing
  • Speed and safety - lock together design and extra clearance O.D.
  • Slide valve - controlled from surface by picking up work string to close and setting down to open
  • Locked in squeeze pressure - the valve automatically closes when the stinger is removed locking in squeeze pressure while excess cement is circulated out
  • Isolates hydrostatic pressure - the valve protects sensitive zone in low fluid level wells
  • 70 mpa (10,000 psi) rated

  

CASING SIZE CASING WEIGHT RETAINER O.D.  SETTING RANGE
MIN. MAX.
in mm ft/lbs kg/m in mm in mm in mm
4.5 114.3 9.5-15.1 14.1-22.5 3.593 91.326 3.826 97.18 4.090 103.89
5 127 11.5-20.8 17.1-31 3.937 100 4.156 105.56 4.560 115.82
5.5 139.7 13-23 19.3-34.2 4.312 109.52 4.580 116.33 5.044 128.12
5.75 146 14-25.2 20.8-37.5 4.700 119.38 4.890 124.21 5.290 134.37
5.63 168.3 17-32 25.3-47.6 5.375 136.53 5.595 142.11 6.135 155.83
7 177.8 17-35 25.3-52 5.688 144.48 6.004 152.50 9.538 166.07
7.63 193.7 28-39 29.8-58 6.312 160.32 6.625 168.28 7.125 180.98
8.63 219.1 24-49 35.7-72.9 7.125 180.98 7.511 190.78 8.097 206.66
9.63 244.5 29.3-58.4 43.6-86.9 8.125 206.38 8.435 214.25 9.063 230.20
10.75 273 32.8-60.7 48.7-90.3 9.437 239.70 9.660 145.36 10.192 258.88
11.75 298.5 38-60 56.5-89.3 10.437 265.10 10.772 273.61 11.150 283.21
11.75 298.5 60-83 89.3-123.5 9.937 252.40 10.192 258.88 10.772 273.61
13.38 339.7 48-80.7 71.4-120 11.875 301.63 12.175 309.25 12.715 322.96
16 406.4 65-118 97.6-175.5 14.125 359.78     15.250 387.35
20 508 94-133 139.8-197.8

18.375

466.73 18.730 475.74 19.124 485.75

Model HM-2 Bridge Plug

 Model HM-2 Bridge Plug

 

The HM-2 Bridge Plug is designed to set with a combination of hydraulic pressure and mechanical pull. Used for temporary or permanent well abandonments and zone isolation.

FEATURES:

  • Competitive cost
  • Constructed with drillable materials
  • Retaining rings to assist in preventing element extrusion
  • Higher temperature of packing element available upon request
  • Sets in p-110 casing
  • 70 mpa (10,000 psi) rated
  • Temperature rating 150 degrees celsius or 300 degrees fahrenheit
  • Right-hand rotation to release work string

 

CASING SIZE CASING WEIGHT PLUG O.D.  SETTING RANGE SURFACE PRESSURE MIN. PULL FORCE MAX. PULL FORCE PRODUCT NUMBER
MIN. MAX.
in mm ft/lbs kg/m in mm in mm in mm psi mPa lbs daN lbs daN
3.5 88.9 5.7-10.3 8.6-15.3 2.750 69.85 2.867 72.82 3.258 82.75 1500 10.3 10,000 4,480 13,000 5,782 350HM2-10
4 101.6 5.6-14 8.3-20.8 3.190 81.03 3.340 84.84 3.732 94.79 1500 10.3 17,000 7,566 20,000 8,896 400HM2-10
4.5 114.3 9.5-16.6 14.1-24.7 3.562 90.47 3.826 97.18 4.090 103.89 1500 10.3 28,000 12,454 30,000 13,344 450HM2-10
5 127 11.5-20.8 17.1-31 3.937 100 4.154 105.51 4.560 115.82 1500 10.3 28,000 12,454 30,000 13,344 500HM2-10
5.5 139.7 13-23 19.3-34.2 4.312 109.52 4.580 116.33 5.044 128.12 1500 10.3 28,000 12,454 30,000 13,344 550HM2-10
5.75 146.1 14-25.2 20.8-37.5 4.699 119.35 4.890 124.21 5.290 134.37 1500 10.3 30,000 13,344 33,000 14,678 575HM2-10
6.63 168.3 17-32 25.3-47.6 5.375 136.53 5.595 142.11 6.135 155.83 1500 10.3 45,000 20.016 50,000 22,240 658HM2-10
7 177.8 17-35 25.3-52.1 5.687 144.45 6.000 152.40 6.538 166.07 1500 10.3 45,000 20.016 50,000 22,240 700HM2-10
7.63 193.7 20-39 29.8-58 6.312 160.32 6.625 168.25 7.125 180.98 1500 10.3 45,000 20.016 50,000 22,240 758HM2-10
8.63 219.1 24-49 35.7-72.9 7.125 180.98 7.310 185.67 8.097 205.66 1500 10.3 45,000 20.016 50,000 22,240 858HM2-10
9.63 244.5 29.3-58.4 43.6-86.9 8.175 207.65 8.379 212.83 9.063 230.20 1500 10.3 45,000 20.016 50,000 22,240 958HM2-8
10.75 273.1 32.7-60.7 48.6-90.3 9.431 239.70 9.660 245.36 10.192 258.88 1500 10.3 45,000 20.016 50,000 22,240 1075HM2-5
13.38 339.7 48-84.5 71.4-125.7 11.880 301.75 12.175 309.25 12.715 322.96 1500 10.3 45,000 20.016 50,000 22,240 1338HM2-3

NOTE: A stabilizer with minimum O.D. of the plug O.D. should be run in conjunction with the plug in a vertical hole. A minimum of two stabilizers should be used in a deviated or directional well.

Model DB Bridge Plug

 Model DB Bridge Plug

 

The DB Bridge Plug is an economical, fully drillable bridge plug and  is suitable for well abandonments or zone suspension.

FEATURES:

  • Competitive cost
  • Constructed with drillable materials
  • Retaining rings to assist in preventing element extrusion
  • Higher temperature of packing element available upon request
  • Sets in p-110 casing
  • Temperature rating 150 degrees celsius or 300 degrees fahrenheit
  • Runs on existing wireline setting tool or hydraulic setting tools

 

CASING SIZE CASING WEIGHT PLUG O.D.  SETTING RANGE SETTING FORCE PRODUCT NUMBER
MIN. MAX.
in mm ft/lbs kg/m in mm in mm in mm lbs daN
9.63 244.5 29.3-58.4 43.6-86.9 8.125 206.38 8.379 212.83 9.603 230.20 50,000 22,240 958DB-8
10.75 269.9 32.7-60.7 48.7-90.3 9.437 239.70 9.660 245.36 10.192 258.88 50,000 22,240 1075DB-5
11.75 298.5 38-60 56.5-89.3 10.437 265.10 10.772 273.61 11.150 283.21 50,000 22,240 1175DB-4
11.75 298.5 60-83 89.3-123.5 9.937 252.40 10.192 258.88 10.772 273.61 50,000 22,240 1176DB-4
13.63 339.7 48-84.5 71.4-125.7 11.880 301.75 12.125 307.98     50,000 22,240 1338DB-3
16 406.4 65-118 96.7-175.5 14.125 358.78     15.250 387.35 50,000 22,240 1600DB-1.5
20 508.0 94-133 139.8-197.8 18.730 475.74 18.730 475.74 19.124 485.75 50,000 22,240 2000DB-1.5



More Articles ...